New Uni-Kit Epson Resetter (version 4.0)

InkGuy · Professional Support Joined: 26 Jul 2005 Posts: 129

UNI-KIT CHIP RESETTER FOR EPSON (VERSION 4.0)

THE UNI-KIT CHIP RESETTER is used to reset the chip on an Epson ink cartridge, and does not change the property of the cartridge itself. In order to reuse an Epson ink cartridge, it needs to be both “reset” and “refilled”.

Resettable Cartridge Models: T068120* / T069120* / T069220* / T069320* / T069420* / T069520* / T077120* / T077220* / T077320* / T077420* / T077520* / T077620* / T078120* / T078220* / T078320* / T078420* / T078520* / T078620* / T007 / T008 / T009 / T015 / T016 / T017 / T018 / T0100 / T026 / T027 / T028 / T029 / T036 / T037 / T038 / T039 / T040 / T041 / T057 / T058 / T066 / T067 / T0321 / T0322 / T0323 / T0324 / T0331 / T0332 / T0333 / T0334 / T0335 / T0336 / T0341 / T0342 / T0343 / T0344 / T0345 / T0346 / T0347 / T0348 / T0422 / T0423 / T0424 / T0431 / T0441 and more.

*For these 9 pin cartridges, please follow special instructions below

Resettable Printer models:
EPSON STYLUS PHOTO:
780 / 790 / 870 / 890 / 895 / 1270 / 1280 / 1290 / 900 / 950 / 2000P / 2100 / 2200 / R260* / R280* / R380* / RX580* and more…
EPSON STYLUS:
C680 / 685 / 777 / 810 / 820 /925 / 830U / C60 / C61 / C62 / C64 / C66 / CX3100 / CX3200 / C41 / C42UX / C43 / C44UX / C45 / C46 / C48 / CX1500 / C70 / C80 / C82 / C82N / C84 / CX4600 / CX5000* / CX6000* / CX5100 / CX5200 / CX5300 / CX5400 / CX6400 / CX6600 and more…
OTHER EPSON:
EPSON TM-C100 / EPSON ME 100/1/1+ and more…

HOW TO USE THE UNI-KIT RESETTER
The pins on the resetter should tightly contact the terminals on the chip of the cartridge, be sure to press against the pins firmly. After a few seconds, the LED indicator will light up and flash about 2~4 times in red, if the LED turns green, it means the resetting operation has been successfully completed. If the LED turns red, it could mean that the chip on the cartridge is abnormal and not resettable. Once the cartridge has been reset, refill it and install it into the printer

IMPORTANT - FOR T068 / T069 / T077 / T078 9-PIN CARTRIDGES:
This Uni-Kit resetter will work on 9 chip cartridges, as shown on the diagram above. The 4 top pins of the resetter must make contact with the 4 top terminals on the chip; the 3 bottom pins of the resetter must make contact with the 3 center terminals on the chip (you do not need to reset the 2 terminals on the chip that are to the far right or far left). Please be sure to refill the cartridge before reinstalling it into the printer.

TROUBLESHOOTING

1. The LED in the universal chip resetter does not flash/turn green.
Answer:
a). Make sure that the pins make good contact with the chip terminals
b). If the design of the chip is different from OEM cartridges, the resetter may have problems trying to recognize it.
2. Cartridges with 9 terminals on the chip could not be recognized*
Answer:
For cartridges with 9 terminals on the chips (T068, T069, T077 and T078 cartridges), the printer reads more than just the chip when determining the ink level status for the cartridge. The printer also reads ink level sensors INSIDE the cartridge, so the cartridge needs to be both properly resetted AND properly refilled in order for the printer to recognize it as full. During the refilling process, air could enter into the sensor areas. Make sure there is no air bubbles inside the cartridge (requires technical know how of refilling these cartridges).

imfong · Joined: 22 Nov 2009 Posts: 3

How do you refill T069's and the T097, Do you just drill a hole on top of it the put a plug on it just like all the others or do you inject it through the outlet hole slowly at a time. Like 4 ml each time slowly.

Oh and will the V4.0 resetter reset the T097 - High Cap. Black/

Printer chips · Joined: 10 Feb 2011 Posts: 14 Location: Lithuania

We could develop any toner cartridge, drum or inkjet chip and more! Your chips supplier can't offer you, you can't find in the market, than we can help Wink